11/09/2019 Furniture News 125 Views

Since its establishment in 1919, Jowat Group has started to provide adhesive products for the wood and furniture industry. During 100 years of development, the adhesive still plays a key role in Jowat’s business with the quality, brand name and reputation affirmed and recognized by customers.

Máy dán cạnh

Along with the overall development of the industry, Jowat has also researched, manufactured and supplied adhesive solutions for various applications of the furniture industry such as:

– Processing wood

– Processing wood-originated materials

– Sofa furniture, seats

– Bedroom furniture

– Cabinets

– Furniture stores, offices

– Details, molding

– Producing doors

In particular, Jowat adhesive is widely applied in finishing door; cabinets; table; kitchen surface; on wood based panel. Edge banding adhesive is also used in room / outdoor; double plate; window skeleton and other household appliances.

Advantages of Jowat edge banding adhesive

Regarding the density, the poor quality adhesive in the market often have high filled content (possibly> 50%). This reduces adhesion and increases consumption per unit area of ​​glue.

Therefore, although the other edge banding adhesives have lower prices than Jowat’s, it takes more consumption. Therefore, more glue must be used. This fact leads to more expensive cost than using high quality adhesive with a good price like Jowat.

Besides, low quality adhesive can not adhere banding such as veneer, ABS … in hard position.

In addition, the poor-quality glue lines often have the phenomenon of glue burning and heavy glue smell due to many impurities. Glue quality is not stable over time when exposed to moisture, temperature …

Caution when using edge banding adhesive

While operating the gluing machine, it is necessary to observe the parameters relating to the operating temperature of the adhesive. Glue surface should be smooth and flat on the edge of the board.

Keo dán cạnh Jowat
Keo dán cạnh Jowat

Besides, the pressure of glue roller on the edge also needs to be installed correctly. Testing can be done before gluing edges by closing the glue knife on the rollers, then testing on MDF boards. If the glue is visible, the roller is in direct contact with the board, then the instructions need to be adjusted.

Ensure the quality of the board before putting it on the edge-gluing line: the board needs to be thoroughly cleaned, well prepared before gluing.

Both board and edge banding must have a minimum temperature of over 18 degrees Celsius. The glue area should also be hygienic, minimizing ingressive dust.

Errors due to improper use of edge banding adhesive

The following errors may be encountered when applying edge banding glue:

– Glue is spinning

– The surface is sticky after being pasted

– Lack of glue at the starting points of edge banding

– Peeling off edge banding

– Swelling board after dehumidification

– Adhesive layer is too thick

– Adhesive layer has holes

– Peeled off at the corner of panel

– Blistering after painting

Keo Jowat
Keo Jowat

These errors may occur depending on the quality of the adhesive; edge setting mode or operating during edge gluing process.

Currently, Minh LongCo., Ltd is distributing 5 Jowat edge banding adhesive products in the North and Central of Vietnam to fully meet the needs for EVA glue:

Jowatherm 282.20: Low temperature edge adhesives (130 – 150 degrees C) for manual gluing machines, post forming line, etc.

Jowatherm 288.60 / 288.61: High temperature edge adhesive (180 – 200 degrees C) meets most common applications. 288.61 is the white version specializing in bright interiors.

Jowatherm 280.50: High temperature edge adhesive for harder surfaces and higher adhesion quality.

Jowatherm 291.60: EVA unfilled adhesive (no filler) for molding, edge application no line manufacture is required

 

 

 

 

Đánh giá bài viết